An aviation maintenance training program is the documented plan an organization uses to show that the people doing maintenance are trained and capable of their assigned tasks. Turning maintenance procedures into training modules means teaching the knowledge around an approved procedure, while the maintenance manual stays the only place where the steps live.
This guide is for training providers and maintenance training teams who build eLearning for repair stations and airline maintenance departments. It is not about technician schools. We are a content authoring vendor, not an aviation authority. We quote regulator text but do not give regulatory advice. Your authority decides what is acceptable.
Key takeaways
- A module should teach the knowledge around a maintenance procedure and link to the current manual. It should not become a second copy of the steps.
- Sort every procedure into three lanes: link, teach and practice. Only the teach lane belongs inside the eLearning.
- Record the source document, revision and review trigger for each module, so a manual revision traces to the modules it affects.
- Ask your authority which module changes count as a training program revision.
What is an aviation maintenance training program, and who approves it?
An aviation maintenance training program is the set of initial and recurrent training that a maintenance organization uses to keep its staff capable of their work. Approval depends on the rule set. In the United States the FAA approves a repair station’s program under 14 CFR Part 145, and European organizations work under EASA Part-145.
According to 14 CFR 145.163, a repair station must have and use an employee training program “approved by the FAA”. The program must ensure each employee assigned to maintenance, preventive maintenance, alteration or inspection is “capable of performing the assigned task”. Individual training records must be documented “in a format acceptable to the FAA”.
The FAA’s Advisory Circular 145-10 (Change 1, July 2012, listed as active on the FAA site as of October 2026) gives guidance on building the program, as one acceptable means of compliance.
In Europe, the EASA Easy Access Rules for Continuing Airworthiness (September 2025 revision) say in 145.A.30(e) that “The organisation shall establish and control the competency of the personnel involved in any maintenance”. For certifying and support staff, 145.A.35(d) requires recurrent training in each two-year period, and 145.A.35(e) requires “a programme for recurrent training”.
Can an aviation maintenance training module copy a maintenance procedure?
A maintenance training module should not copy a maintenance procedure as a second source of steps. Regulations expect technicians to work from current approved data, so the module should build understanding and point to the manual. Copied steps go stale when the manual changes, and a technician could follow a superseded revision.
14 CFR 43.13(a) says a person performing maintenance “shall use the methods, techniques, and practices prescribed in the current manufacturer’s maintenance manual” or the manufacturer’s Instructions for Continued Airworthiness, or other methods acceptable to the Administrator. For repair stations, 14 CFR 145.109(d) says maintenance manuals, service bulletins and airworthiness directives must be “current and accessible when the relevant work is being done”. EASA 145.A.45(a) says the organization “shall hold and use applicable current maintenance data”.
The design rule that follows is ours, not a regulator’s: the manual instructs and the module teaches. A screen may show a step to explain it, labeled as an illustration with a link to the controlled document.
How do you sort a maintenance procedure into what a module can carry?
Sorting a maintenance procedure into three lanes shows what an eLearning module can carry. Lane 1 is link-only content such as steps and limits. Lane 2 is teach content such as purpose and error awareness. Lane 3 is practice content that stays hands-on. Run every task through the lanes before writing a screen.
| Lane | What goes in it | Where it lives | Revision trigger |
|---|---|---|---|
| 1. Link, never copy | Step sequences, limits, torque values, part numbers, warnings and cautions as written | The controlled manual or task card; the module links to the current revision | Any revision of the source document |
| 2. Teach | Purpose of the task, system context, why the steps matter, how to find the current revision, error patterns | The module | A change in intent, tools or error patterns, plus a scheduled review date |
| 3. Practice and sign-off | Tool handling, hands-on skill, first supervised performance | On-the-job training with a qualified person, recorded under your program | A change in the task method or sign-off standard |
A quick test settles most cases: if a screen holds a number or step a technician could act on, it is lane 1 and becomes a link. Our guide to SOP to training covers general task analysis.
Pro tip: Tag Every Screen With Its Source. Add a small source line to each lane 2 screen with the manual ID, revision and date used at build. A reviewer can check the screen against one document, and a revision notice can be matched to screens by search.
How do you build an aviation maintenance training program module from one procedure?
Building an aviation maintenance training program module from one procedure takes six steps: confirm the training need, lock the source, sort the content into lanes, choose the method, build judgment checks, and review. Fix the source and the lanes before writing any screen.
- Confirm the need. AC 145-10 paragraph 401 describes a needs assessment based on job positions, duties and tasks. Start from the task a person is assigned, not the document you have.
- Lock the source. Record the manual or task card ID, revision and date.
- Sort into lanes. Mark each task 1, 2 or 3 using the table above.
- Choose the method. AC 145-10 paragraph 403 lists classroom, on-the-job training, computer-based training, distance learning, embedded training and self-study. It says “Interactive CBT courses can be used to impart knowledge and teach practical skills at the correct pace for each employee.” That is guidance. Your program states your methods.
- Build judgment checks. Ask what the technician does when a situation is unclear, not which step is third.
- Review and measure. AC 145-10 paragraph 406 says “the training program should have a method to evaluate whether the training has been effective.” Plan a practical check after the module, not only a quiz score.
Our course production workflow from SME to publish sets review gates that fit here.
What should a module source record contain?
A module source record is a one-page entry kept for each module that ties it to its source document, program category and review trigger. It is our template, not a regulatory form, for answering one question quickly: which modules does this manual revision affect?
| Field | What to record |
|---|---|
| Module and version | Title, version number, build date |
| Source document | Manual or task card ID, revision, date, location of the controlled copy |
| Program category | Where it sits in your program: indoctrination, technical, recurrent, specialized or remedial (the AC 145-10 categories) |
| Lane map | Lane 1, 2 or 3 for each task, and the link targets |
| Sign-off and reviewers | Module alone or with a practical check, who signs, review dates |
| Revision trigger | Manual revision, service bulletin, internal finding or scheduled date |
Which changes to an aviation maintenance training program need approval?
Which changes to an aviation maintenance training program need approval depends on your authority and your approved program, so ask before you build. The FAA rule shows the pattern: the training program is approved, and revisions follow a procedure written into the repair station manual.
For a US repair station, 14 CFR 145.209(e) calls for “Procedures for revising the training program” and “submitting revisions to the responsible Flight Standards office for approval”. AC 145-10 notes in its preface that when a station adds nonregulatory subjects, only those required by regulation are subject to FAA approval.
A module may or may not be part of the approved program, and an edit may or may not be a program revision. We cannot answer that for you. Approval attaches to the organization’s program, not to a tool or file format. Ask your inspector or authority contact:
- Which module types are part of the approved program, and which are supporting material?
- Does a revised module need a program revision, or only an internal revision?
- Is an LMS completion record an acceptable training record format?
- Which revision events require retraining, and who decides?
How do you keep modules current when the manual changes?
Keeping aviation maintenance training modules current when the manual changes needs a trace from every manual revision to the modules built on it. Use the source record to find affected modules, check each lane 2 screen against the new revision, and republish with a new version number.
14 CFR 145.109(d) and EASA 145.A.45(g), which requires “a procedure to ensure that maintenance data it controls is kept up to date”, both expect current data. Training that cites a superseded revision works against both. On a revision notice, run this routine:
- Search the source records by document ID.
- Compare each affected module’s lane 2 screens with the new revision.
- Relink lane 1 references. Never edit lane 1 content inside the module.
- Decide with your training owner whether learners need a refresher.
Our guide to course version control when regulations change covers the general routine.
What stays hands-on, and how do modules support on-the-job training?
Aviation maintenance on-the-job training stays hands-on because the skill is performed with tools on real tasks. AC 145-10 describes it as “knowledge obtained while participating in accomplishing the task under the direction of a qualified person”. A module prepares the learner for that supervised work. It does not replace it.
Use the module before the supervised task for lane 2 content, and use the on-the-job record for lane 3. An April 2011 D.O.M. Magazine article by Thomas Shecker recommends recording each on-the-job event as satisfactory or unsatisfactory. It also warns that pressure to deliver all training online can compromise hands-on learning.
Some procedures need a job aid instead; see our comparison of job aids vs eLearning. AC 145-10 also says the submitted program “must include human factors elements”; see human factors training for maintenance staff.
Pro tip: Turn Your Own Findings Into Scenarios. Rewrite de-identified internal findings as knowledge checks: describe the situation, ask what the technician checks first, and let the feedback point to the manual section. Get quality department approval first and remove names and tail numbers.
Where do SimpliAuthor and SimpliTrain fit?
SimpliAuthor and SimpliTrain can support building and tracking lane 2 modules, but approval attaches to your program, not to either tool. Disclosure: SimpliAuthor is a SimpliTrain product and the same company publishes this site, so read this as vendor content.
Based on the vendors’ published pages as of October 2026, and untested by us: the SimpliAuthor AI course authoring page says its AI reads “prompts, documents, URLs, product guides, SOPs, and HR policies”, then maps an outline and builds editable blocks, including assessments. The SimpliTrain aviation page describes a combined training management and learning management system, and says it supports SCORM 1.2, xAPI and cmi5. Before uploading a controlled manual to any AI tool, check its license terms and your data policy, and have a qualified SME review each screen.
What should you do next?
Pick one procedure technicians already perform and run the three-lane sort on it this week. Fill in a source record and see how much of the document is link-only content. Then take the four questions above to your authority contact and write down the answers.
Frequently asked questions
Does an aviation maintenance training program have to be approved?
For a US repair station, yes. 14 CFR 145.163 requires an employee training program “approved by the FAA”. Under EASA Part-145, the organization establishes and controls competence under 145.A.30(e) and keeps a recurrent training programme for certifying and support staff. Confirm what applies to your approval with your authority.
Can eLearning be used for repair station training?
AC 145-10 paragraph 403 lists computer-based training and distance learning among training methods and says interactive CBT can teach knowledge and practical skills. That is guidance, not approval. Your approved program sets which methods you may use, so check with your authority before replacing any classroom or on-the-job element.
How often is recurrent maintenance training required?
EASA 145.A.35(d) requires recurrent training for certifying and support staff in each two-year period. For a US repair station, 14 CFR 145.163 requires initial and recurrent training, and the program you submit defines the cycle. Ask your FAA inspector how your program should state it.
Should a training module include the full maintenance procedure?
No. Rules such as 14 CFR 43.13(a) and EASA 145.A.45 expect work to follow current maintenance data. A module that copies the steps creates a second version that can go out of date. Teach purpose, risks and decisions, and link to the manual for the steps.
How long must maintenance training records be kept?
AC 145-10 paragraph 407 says records should be “retained for a minimum of 2 years”, and 14 CFR 145.163 requires documenting individual training in a format the FAA accepts. Your contracts or authority may require longer. Confirm the retention period and record format before you rely on LMS exports.


